JD65-XT Kit - Wall

Unlimited Call Capacity
65dB Gain / 13dBm Output Power
FCC Approved. ID: SQXJD65-XT
18 Months Warranty
30 Day Money Back Satisfaction Guarantee
MUTE - Auto Shut Down if oscillation is detected
Medium-Sized Coverage Area (5000 - 6000 Sq ft)
Manual Gain Control Feature (Tx & Rx)
Alarm LED's for Error Detection
Attractive modern design
Wide range of frequencies available
Supports 90-265 Volts / 50-60Hz
AGC: Automatic Gain Control
ALC: Automatic Limit Control
Supports Any Cellular Device (Voice & Data)
Free! - Phone Tech Support
Kit includes 2 Wall Mounted High Gain Directional Antennas
Easy to Install

Select Optional Coax Length

Mhz	Add to Cart	Option
800 / 850	$764.95	A
900	$764.95	B
1800	$764.95	C
1900	$764.95	D
800 / 1900	$944.95	E
900 / 1800	$944.95	F
900 / 2100	$944.95	G
1900 / 1721	$1019.50	H

A -Single Band USA (GSM,CDMA,GPRS,EDGE)
B - Single Band Global (GSM)
C - Single Band Global (GSM,DCS)
D -Single Band USA (GSM,PCS,CDMA,EDGE,3G)
E -Dual Band USA (GSM,CDMA,GPRS,EDGE,PCS,3G)
F -Dual Band Global (GSM,DCS)
G -Dual Band Global (GSM,3G,UMTS,WCDMA)
H - Dual Band USA (PCS, AWS)

(Click here for User Manual)

Add to Wishlist

Features

The JD65-XT Dual Wall Cell Phone Repeater Kit is supplied with 2 Wall Mounted Panel Antennas and includes all the peripheral items needed to complete the installation. This kit is designed to provide cellular coverage (voice & data) for a building up to 6,000sq ft. and is perfect for providing wireless coverage inside a medium sized home, office building, restaurant, warehouse, underground parking lot, VIP room, etc.

At the heart of kit is a full duplex 65dB Gain Dual Band repeater that includes carrier grade features like Automatic Gain Control (AGC), Manual Gain Control and MUTE Auto Shut Down to name a few. The standard kit is supplied with a 35ft length of coax that runs from the outdoor antenna to the repeater and 35ft of coax from the repeater to each service antenna. You have the option to customize these coax length as needed. (Minimal additional cost).

Standard Kit Includes:

Yagi Donor Antenna with U Bolts
35ft Length of Coax - Donor
JD65-XT Repeater & Power Supply
N Male / N Male RF Adapter
2-Way Signal Splitter
35ft Length of Coax - (2)
Wall Mount Panel Antennas - (2)
Coax Seal
User Manual
Warranty Card
Free Technical Phone Support

To maintain safe and specific output signal levels, this advanced repeater has built-in AGC and ALC circuits, which can automatically control the gain of the repeater within a 15dB range depending on environmental conditions. In addition, it also has built-in attenuation dip switches that allow you to manually attenuate (fine tune) the repeater's uplink and downlink channels in 1db steps up to 31dB, using color changing LED's as a status indicator.

These Alarm LED's are used as a guide to prevent your installation from re-producing errors due to excessive input signal strength if a pre-amp is used, or from signal oscillation due to the indoor antenna and outdoor antenna being too close to each other, which can have adverse effects on a base station.

A Network Safe / MUTE Feature has also been added to this repeater to protect the cellular network. In short, the repeater will stop transmitting if any errors or signal oscillation is detected within 2 sec of detection. It will cycle for 30 sec then attempt to transmit again. If no adjustment in gain has been made to correct the error within the 30sec MUTE cycle, the system will again shut down after 2 sec. It will run this sequence for a total of 3 times and then shut down completely. Unplugging and powering back up the unit will reset this sequence. The JD65-XT Indoor Repeater is designed to be transparent to the network and will therefore support the same number of calls the BTS in the area can support. It is also compact enough that it can be placed within an electrical closet where space is limited.

Specifications

Frequency & Operating Mechanical

FCC Approved		ID: SQXJD65-XT	Input / Output RF	N Female
Maximum Gain		≥ 60dB	Dimension	H* W * D = 183 x 128 x 46.3 (mm)
Gain Flatness (P-IP)		GSM850 / CDMA / GSM ≤ 8dB DCS / PCS ≤ 10dB WCDMA ≤ 6dB	Cooling	Convection
			Weight	< 1 kg / 2.2Lbs
Noise Figure		≤ 5dB	Operating Temperature	-10'C ~ 50'C / 14F - 122F
AGC Range		20dB	AC/DC Power Supply	Input AC 90-265v , Output DC 9V
Output Power		UL ≥10dBm, DL ≥10dBm	Weather Proof	IP 40
Propagation Delay		≤ 0.5 us (micro second)
Frequency Stability		≤ +- 0.01 ppm
Impedance		50 Ohms
ACRR	WCDMA	≥30dB ＠±5MHz＆±10MHz
Spurious Emission		Complies with 3GPP TS 25.106
Modulation Accuracy		Complies with 3GPP TS 25.106
Intermodulation Products		Complies with 3GPP TS 25.106
Spurious Emission Mask		Complies with 3GPP TS 25.106
Peak Code Domain Error		Complies with 3GPP TS 25.106

Bandwidth & Part Numbers

A. Frequency Range
(USA Cellular - CDMA, GSM)
Part # JD65-XT850

Forward Path

869-894 (MHz)

Reverse Path

824-849 (MHz)

B. Frequency Range
(GSM European) & Paging Systems
Part # JD65-XT900 Forward Path 935-960 (MHz)

Reverse Path 890-915 (MHz)

C. Frequency Range
(European DCS)
Part # JD65-XT18 Forward Path 1805-1880 (MHz)

Reverse Path 1710-1785 (MHz)

D. Frequency Range
(USA - PCS / CDMA / GSM / GPRS)
Part # JD65-XT19 Forward Path 1930-1990 (MHz)

Reverse Path 1850-1910 (MHz)

E. Frequency Range
(USA - PCS / CDMA / GSM / GPRS)
Part # JD65-XT819 Forward Path 869-894 / 1930-1990 (MHz)

Reverse Path 824-849 / 1850-1910 (MHz)

F. Frequency Range
(European - GSM / DCS)
Part # JD65-XT918 Forward Path 935-960 / 1805-1880 (MHz)

Reverse Path 890-915 / 1710-1785 (MHz)

G. Frequency Range
(European - 900 / 3G)
Part # JD65-XT921
Forward Path
935-960 / 2110-2170 (MHz)

Reverse Path
890-915 / 1920-1980 (MHz)

H. Frequency Range
(USA - PCS / AWS)
Forward Path
1930-1990 / 2110-2155 (MHz)

Reverse Path 1850-1910 / 1710-1755 (MHz)

Download PDF Brochure

Click here to Download